ABOUT

Solutions & Cases

Our Case
  • Improved balance between compressive strength and

    Aluminum filter: 1.0 mm : Rotation: 360° The increase of coarse and fine expanded clay volumes reduces the compressive strength because their intrinsic strength is lower than those of normal weight aggregates and the mortar phase, as evidenced in the literature,,,, . In the present study, the volume proportion increase of CEC presents a higher reduction of the 120 days compressive

  • Sintering of alumina powder compacts and their

    The slopes of the linear approximations of the plots represent the compressive strength of dense alumina without pores (effective compressive strength, σ 0, in Eq. (3) ). The σ 0 values for AKP50, AKP30 and AKP20 were all 1.91 GPa, which was slightly less than previously reported values for dense, polycrystalline alumina ( σ 0 =2.2 GPa [17] and 2.6 GPa [18] ).

  • 23 Types of Concrete Used in Construction and their

    The compressive strength is 200 to 500 kg/cm 2. These types of concrete are mainly used in the construction of the pavements and the buildings, especially in areas where there is less demand of high tensile strength. The durability given by these type of concrete is satisfactory to high extent.

  • Models of Rotary Vacuum Drum and Disc Filters for

    Models of Rotary Vacuum Drum and Disc Filters for Flocculated Suspensions. Article in AIChE Journal 57(4):951 961 · April 2011 with 1,371 Reads How we measure 'reads' A 'read' is counted each

  • Disc filter Wikipedia

    Disc filters can be used for many types of contaminants, including fine sand and organic matter. However, when used to filter organic matter, they will clog more quickly than a media filter and will have to be cleaned more often. One advantage that the disc filter has over the media filter is that it can backflush more quickly with less flush water. Disc filters used in agricultural irrigation

  • STRENGTH PROPERTIES OF ROCKS AND ROCK MASSES 1

    Table 2. Mean tensile strength and compressive strength for selected sedimentary rock types (after Johnson and Degraff, 1988). The behavior of intact rock in the post-peak dom ain is not a true rock property and is partially dependent on the stiffness of the loading system. A

  • 19 Types of Composite Material Simplicable

    19 Types of Composite Material posted by John Spacey, This is done to produce materials with desirable properties such as high compressive strength, tensile strength, flexibility and hardness. The following are illustrative examples. Reinforced Concrete Concrete has a low tensile strength and is often improved by embedding a structure made from a material with high tensile strength such as

  • Chapter 1 Tension, Compression, and Shear

    Chapter 1 Tension, Compression, and Shear 1.1 Introduction Mechanics of Materials : to understand the behavior of solid bodies subjected to various types of loading This course have several names : "Strength of Materials", "Mechanics of Deformable Bodies" Two main aspects: 1. stress analysis : analysis of bodies under the action of external force, to determine the internal stress and their

  • Types of Air Compressors: Reciprocating, Rotary, Screw

    Read here to know about various types of air compressors used and get a clear inside view of each type of compressor with the attached pictures. Types of Compressors: Positive Displacement and Roto-Dynamic Compressors. Positive displacement compressors cab be further divided into Reciprocating and rotary compressors. Types of rotary compressor: Screw compressors, Vane type compressors, Lobe

  • Sintered Metal Filters: The Ultimate Guide Filson Filter

    Chapter 6: Types of Sintered Metal Filters. There are different types of sintered metal filters that you can find in the market. However, the choice of which one to use depends on your application. To enable you to make the right choice when choosing a sintered metal filter, here is a look at the common types available in the market. 6.1

  • Ceramics for Strength San Jose Delta

    Ceramics tend to be weak in tension, but strong in compression. For a metal, the compressive strength is near that of the tensile strength, while for a ceramic, the compressive strength may be 10 times the tensile strength. Alumina, for example, has a tensile strength of 20,000 psi 1138 MPa), while the compressive strength is 350,000 psi (2400 MPa).

  • MECHANICAL PROPERTIES OF MATERIALS

    •Three types of static stresses to which materials can be subjected: 1. Tensile tend to stretch the material 2. Compressive tend to squeeze it 3. Shear tend to cause adjacent portions of material to slide against each other •Stress-strain curve basic relationship that describes mechanical properties for all three types

  • Evaluation of the performance of shotcrete in structural

    Evaluation of the performance of shotcrete in structural rehabilitation Marta Oliveira dos Santos AFA, Air Force Academy, Portugal IST, Technical University of Lisbon, Portugal [email protected] Abstract: Shotcrete is a continuous method of projecting concrete at high velocity, without the help of any formwork. This technique is being used, with great success, in the rehabilitation of

  • Different Steel Types and Properties ThoughtCo

    Different types of steel are produced according to the properties required for their application, and various grading systems are used to distinguish steels based on these properties. Steel can be broadly categorized into four groups based on their stone compositions: Carbon Steels; Alloy Steels; Stainless Steels; Tool Steels; The table below shows the typical properties of steels at room

  • Concrete -Definition, Components, Grades, Manufacture

    Generally, strength of concrete in tension is only 10% of its strength in compression. It is used as a construction material for almost all types of structures such as residential concrete buildings, industrial structures, dams, roads, tunnels, multi storey buildings, skyscrapers, bridges, sidewalks and superhighways etc. Example of famous and large structures made with concrete are Hoover Dam

  • INTACT ROCK STRENGTH UNDER TRIAXIAL COMPRESSION AND

    i) and their behaviour is studied. A discussion, concerning the influence of the uniaxial compressive strength, σ ci, the tensile strength, σ t, of intact rock and the range of confining

  • DESIGN RECOMMENDATION FOR STORAGE TANKS AND THEIR

    became possible to ascertain the buckling strength by experiments on a cylindrical shell by applying an internal hydrodynamic pressure, an axial compressive force, and a shear force simultaneously. Details of these experiments are given in Chapter 3. The seismic design calculations for other types of storage tanks have been similarly reviewed

  • PROPERTIES OF THE POLYURETHANE (PU) LIGHT FOAMS

    The compression tests were carried out according to ISO 844 Standard in parallel and perpendicular direction to the foam rise. Specimens’ dimensions were 100x100x50 mm. The used equipment is shown in Photo 1. The compression strength and rigidity modulus were measured for both foams. For the foam of 62 kg/m3 density compressive

  • 3 Types of Air Compressors (Plus Benefits and Comparison)

    Every type uses a distinct air compressor filter. Other classification may be based on: • How each works (low, medium, high) • The number of compression stages (single-stage, 2-stage, and multi-stage) • Cooling method (air, water or oil) • Drive method (direct-coupling, gear, turbine, chain, belt, motor, engine, steam) • Lubrication method (either splash, forced lubrication, oil or