ABOUT

Solutions & Cases

Our Case
  • Aggregates Portland Cement Association

    Aggregates, which account for 60 to 75 percent of the total volume of concrete, are divided into two distinct categories--fine and coarse. Fine aggregates generally consist of natural sand or crushed stone with most particles passing through a 3/8-inch sieve. Coarse aggregates are any particles greater than 0.19 inch, but generally range between 3/8 and 1.5 inches in diameter. Gravels

  • Different Types & Sizes of Aggregate for Concrete

    It includes gravel, crushed stone, sand, slag, recycled concrete and geosynthetic aggregates. For a good concrete mix, aggregates need to be clean, hard, strong particles free of absorbed chemicals or coatings of clay and other fine materials that could cause the deterioration of concrete. SIZES OF AGGREGATE

  • Aggregate in Concrete The Concrete Network

    Fine aggregate should fall within gradation limits provided in ASTM C 33, Section 6. If there is a deficiency in a locally available fine aggregate, concrete may benefit from the addition of air entrainment, additional cement, or a supplemental cementitious material (SCM) to address these shortcomings. Broad coarse-aggregate gradation ranges are listed in Table 2 of ASTM C 33. These

  • Fine Aggregate: Definition, Size, Density and Properties

    Fine aggregate is the essential ingredient in concrete that consists of natural sand or crushed stone. The quality and fine aggregate density strongly influence the hardened properties of the concrete.. The concrete or mortar mixture can be made more durable, stronger and cheaper if you made the selection of fine aggregate on basis of grading zone, particle shape and surface texture, abrasion

  • Aggregates Types of Aggregates Coarse Aggregate, Fine

    Aggregate is a granular material, such as sand, gravel, crushed stone, crushed hydraulic-cement concrete, or iron blast-furnace slag, used with a hydraulic cementing medium to produce either concrete or mortar. Types of aggregates include Coarse aggregate and fine aggregate. The aggregate of each type is further sub-divided into many types and classification based on its size. The technique of

  • WHAT ARE THE PROPERTIES OF AGGREGATES FOR

    The size and shape of the aggregate particles greatly influence the quantity of cement required in concrete mix and hence ultimately economy of concrete. For the preparation of economical concrete mix on should use largest coarse aggregates feasible for the structure. IS-456 suggests following recommendation to decide the maximum size of coarse aggregate to be used in P.C.C & R.C.C mix.

  • What is the difference between fine aggregate and coarse

    Fine Aggregate : If the aggregate size is less than 4.75mm, then it is called as Fine aggregate. The minimum size of fine aggregate is 0.075mm is preferred for concreting works Coarse Aggregate : If the aggregate size is more than 4.75mm, then it

  • Difference Between Fine and Coarse Aggregate Civil

    Fine Aggregate vs Coarse Aggregate. Fine and coarse aggregates have some major differences. Sources of main differences between deep and shallow footings are definition, size of particles, materials, sources, surface area, function in concrete, uses, etc. In the following table the main differences between Fine and coarse aggregate are given:

  • Aggregates for Concrete

    AGGREGATES FOR CONCRETE E1-3 sieve and predominantly retained on the 75 µm (No. 200) sieve is called “fine aggregate” or “sand,” and larger aggregate is called “coarse aggregate.” Coarse aggregate may be available in several different size groups, such as 19 to 4.75 mm (3/4 in. to No. 4), or 37.5 to 19 mm (1-1/2 to 3/4 in.).

  • Aggregates for Concrete Memphis

    aggregates cannot be overemphasized. The fine and coarse aggregates generally occupy 60% to 75% of the concrete volume (70% to 85% by mass) and strongly influ-ence the concrete’s freshly mixed and hardened proper-ties, mixture proportions, and economy. Fine aggregates (Fig. 5-1) generally consist of natural sand or crushed

  • How to calculate cement, sand and coarse aggregate for

    How to Calculate Cement, Sand and Coarse Aggregate for Concrete? 4 Mins Read. Share. Share on Facebook Share on Twitter Email. Estimation of any material looks daunting until unless you learn the nitty, gritty of the calculation. In this post, We are going to discuss the concrete material calculation with an example. For Slab calculation ( 5m x 2m x 0.1m) For Beam calculation ( 5m x 2m x 0.3m

  • Aggregates for Concrete

    AGGREGATES FOR CONCRETE E1-3 sieve and predominantly retained on the 75 µm (No. 200) sieve is called “fine aggregate” or “sand,” and larger aggregate is called “coarse aggregate.” Coarse aggregate may be available in several different size groups, such as 19 to 4.75 mm (3/4 in. to No. 4), or 37.5 to 19 mm (1-1/2 to 3/4 in.).

  • Concrete using agro-waste as fine aggregate for

    Concrete is a mixture of cement, fine aggregate and coarse aggregate, which is mainly derived from natural resources. Increasing population, expanding urbanization, climbing way of life due to technological innovations has demanded a huge amount of natural resources in the construction industry, which has resulted in scarcity of resources. This scarcity motivates the researchers to use, solid

  • Importance of Gravel and Sand for Concrete Hunker

    Importance of Gravel and Sand for Concrete By Deborah Ng Updated April 12 Use the fine aggregate for concrete slabs or other smooth surfaces. A "coarse" aggregate means using larger pieces of gravel. Coarse concrete is helpful for sturdier projects. Concrete with a coarse aggregate doesn't produce a smooth look or feel but is stronger than a finer grade. Most home improvement

  • Aggregates for Use In Concrete

    Aggregates for Use In Concrete 2 Learning Objective • Develop a basic understanding of aggregates and aggregate properties. 2/12/2015 2 3 Aggregates • Fine Consists of natural sand, manufactured sand or crushed stone <3/8” Fine aggregate will pass the # 4 sieve • Coarse Natural or crushed stone 3/8” to 1 ½” (or more) Coarse aggregate is larger than a #4 sieve 4 Mineralogy

  • Aggregates for concrete Aggregates sizes for concrete

    Introduction for Aggregates for concrete. Hi friends, here i am going to tell you the different aggregates sizes for concrete which are generally used for preparing different grades of concrete. Different sizes of aggregate are used for concrete and are necessary if we required good quality of concrete.

  • MATERIAL SPECIFICATION FOR AGGREGATES CONCRETE

    1002-B Concrete Aggregate Test Data Fine Aggregate . 1002-C Concrete Aggregate Test Data Coarse Aggregate . 1002.01 SCOPE . This specification covers material requirements for aggregates for use in Portland cement concrete. Quality Control and Quality Assurance procedures and referee testing protocol are incorporated.

  • How Coarse Aggregate Affects Mix Design of Concrete?

    Coarse aggregate is one of the essential components of concrete and occupies the largest volume in the mix. That is why it greatly affects the concrete mix design. Its properties such as strength, maximum size, shape, and water absorption influence water demand, the quantity of cement and fine aggregate in concrete mixture. It is reported []

  • Fine-Aggregate Concrete Article about Fine-Aggregate

    Fine-Aggregate Concrete (or fine-grained concrete), concrete produced from a mixture of fine aggregate (sand), a binder (cement), and water. Fine-aggregate concrete is similar to building mortars in its composition and certain properties. It is used mainly for making thin-walled and conventional rein-forced-concrete structural components and products